Flashings
- All products
- Hybrid Stoves6 products
Room Stoves158 products
Airtight Stoves122 products
Ductable Stoves64 products
Slimline Stoves40 products
Insert Stoves42 products
Boiler Stoves60 products
Range Cookers9 products
Outdoor Fires & BBQ6 products
Boilers13 products
Pellet Flue195 products
Accessories17 products
Showing all 7 results
No 4 Metal Black EPDM
€27.00
No 4 Metal Black EPDM 76-152mm 250x250
APPLICATION
Suitable for profiled sheeting and flat panel surfaces and is temperature resistance -55°C to 135°C.
CONSTRUCTION
Made of EPDM, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light.
The one piece construction allows for quick and easy on-site installation - usually taking no longer than five minutes.
The base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.
INSTALLATION
1. Choose pipe opening and trim using a stanley knife or scissors.
2. Slide flashing over pipe (you may need to lubricate the flashing with some grease).
3. Form the flashing to the same profile as the roof.
4. Apply sealant (contained in the Fixing Kit).
5. Fasten using the screws and caps (supplied in the Fixing Kit).
ONE Standard Fixing Kit is required to install this flashing.
No 4 Metal Grey SILICONE
€41.50
No 4 Metal Grey SILICONE 76-152mm 250x250
APPLICATION
Suitable for profiled sheeting and flat panel surfaces and is temperature resistance -74°C to 260°C
CONSTRUCTION
Made of SILICONE, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light.
The one piece construction allows for quick and easy on-site installation - usually taking no longer than five minutes.
The base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.
INSTALLATION
1. Choose pipe opening and trim using a stanley knife or scissors.
2. Slide flashing over pipe (you may need to lubricate the flashing with some grease).
3. Form the flashing to the same profile as the roof.
4. Apply sealant (contained in the Fixing Kit).
5. Fasten using the screws and caps (supplied in the Fixing Kit).
ONE Standard Fixing Kit is required to install this flashing.
Size 1 High Temp Grey SILICONE Size 80-200mm
€80.00
Suitable for tiled or slate roofs with external pipe diameters of 80mm to 200mm
The aluminium base size is 605mm x 505mm, suitable for high temperatures
APPLICATION
Suitable for tiled roofs and is temperature resistance -74°C to 260°C
CONSTRUCTION
Enviromentally safe lead free aluminium base. The SILICONE rubber upstand has a 20 year life. The built in 20° pitch allows adaptability to almost any roof pitch including 45°. The pull tab design and easy smooth tear grooving is intended to eliminate cutting by knife and allow for a circular hole.
INSTALLATION
1. Pull tab design to correct size using pliers, alternatively cut using a stanley knife.
2. Apply silicone sealant to back of flashing.
3. Remove tiles around pipe and slide flashing over pipe.
4. Fasten Flashing to the roof.
5. Cut tile to fit to the top of the Flashing allowing the bottom of the flashing metal base to sit on top of the tiles.
Size 1 Low Temp Black EPDM Size 80-200mm
€38.00
Suitable for tiled or slate roofs with external pipe diameters of 80mm to 200mm
The aluminium base size is 605mm x 505mm, suitable for low temperatures
APPLICATION
Suitable for tiled roofs and is temperature resistance -55°C to 135°C
CONSTRUCTION
Enviromentally safe lead free aluminium base. The EPDM rubber upstand has a 20 year life. The built in 20° pitch allows adaptability to almost any roof pitch including 45°. The pull tab design and easy smooth tear grooving is intended to eliminate cutting by knife and allow for a circular hole.
INSTALLATION
1. Pull tab design to correct size using pliers, alternatively cut using a stanley knife.
2. Apply silicone sealant to back of flashing.
3. Remove tiles around pipe and slide flashing over pipe.
4. Fasten Flashing to the roof.
5. Cut tile to fit to the top of the Flashing allowing the bottom of the flashing metal base to sit on top of the tiles.
Size 1 Low Temp Black EPDM Size 80-200mm Lead Base
€138.00
Suitable for tiled or slate roofs with external pipe diameters of 80mm to 200mm
The lead base size is 605mm x 505mm, suitable for low temperatures
APPLICATION
Suitable for tiled roofs and is temperature resistance -55°C to 135°C
CONSTRUCTION
Enviromentally safe lead free aluminium base. The EPDM rubber upstand has a 20 year life. The built in 20° pitch allows adaptability to almost any roof pitch including 45°. The pull tab design and easy smooth tear grooving is intended to eliminate cutting by knife and allow for a circular hole.
INSTALLATION
1. Pull tab design to correct size using pliers, alternatively cut using a stanley knife.
2. Apply silicone sealant to back of flashing.
3. Remove tiles around pipe and slide flashing over pipe.
4. Fasten Flashing to the roof.
5. Cut tile to fit to the top of the Flashing allowing the bottom of the flashing metal base to sit on top of the tiles.
Standard Fixing Kit
€19.50
Storm Collar – Ø 80
€20.00
Used to ensure water tightness in the passage through the roof.
It also protects the flashing from extreme weather conditions. Its should be installed about 25mm above the tallest part of the flashing
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.