Adjustable Base Support – Ø 80
Adjustable Base Supports are used to provide vertical supports to the chimney
This support has a small levelling adjustment of 50mm to 80mm from the wall surface
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Guy Wire Bracket – Ø 80
This component is used to secure unsupported sections above 1.5m of the roof level.
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Guy Wire Kit 30m
The Guy Wire Kit is the ideal solution to support a high or unsteady chimney
All parts are made from rustproof galvanised steel, the kit contains enough parts to make three 10m long supporting wires.
CONSTRUCTION
All components are made from rustproof Galvanised Steel.
The wire rope is constructed from 3mm diameter galvanised steel made from 7 twisted sets of 19 strands making it ideal for straining / guy wires.
INSTALLATION
STEP 1.
Secure the GUY WIRE BRACKET (not supplied) to your chimney.
STEP 2.
Pass the 3mm Wire Rope through the Wire Rope Grip to create loop.
STEP 3.
Insert the Thimble inside the loop and tighten the Wire Rope Grip using the nuts until the Thimble is secure.
STEP 4.
Unscrew the D-Shackle and pass through the loop.
STEP 5.
Attached the Barrel Strainer via the EYE by passing through the threaded bar component of the D-Shackle.
STEP 6.
Secure the Hook and Eye Strainers to either bolts or screws that have been secured into masonry.
PACK CONTENTSN
30m of 3mm diameter glavanised steel wire rope.
6 - D-Shackles.
6 - Thimbles
12 - Wire Rope Grips.
3 - Hook and Eye Barrel Strainers.
Joist Support – Ø 80
Joist supports are used to support the chimney as it passes through floor joists.
The joist support is used in conjunction with the fire stop plates and is fixed on the upper floor section spanning the floor joist allowing even weight distribution
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Locking Band – Ø 80
The Locking band is used to secure two parts of the flue together, A locking band is required at every joint.
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Roof Support – Ø 80
The Roof Support will rotate on 2 screws so that the flue can be installed vertically through the roof.
The roof support is attached to the rafters in the roof space allowing a fixed support before the flue leaves the structure of the building.
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Structural Locking Band – Ø 80
The Structural Locking Band replaces the standard lacking band when unsupported length of up to 2.9m is required.
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Wall Support 130mm-210mm – Ø 80
Wall support are to be used for lateral support only and should be a minimum of every 3 meters
Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 80mm min and 420mm max adjustment from the wall.
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Wall Support 210mm-420mm – Ø 80
Wall support are to be used for lateral support only and should be a minimum of every 3 meters
Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 80mm min and 420mm max adjustment from the wall.
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Wall Support 50mm-80mm – Ø 80
Wall support are to be used for lateral support only and should be a minimum of every 3 meters
Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 80mm min and 130mm max adjustment from the wall.
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Wall Support 80mm-130mm – Ø 80
Wall support are to be used for lateral support only and should be a minimum of every 3 meters
Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 130mm min and 210mm max adjustment from the wall.
ConvesaTWPro Fit System
Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next.
APPLICATION
For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
