Click to enlarge
Size 1 Low Temp Black EPDM Size 80-200mm Lead Base €138.00
Back to products
No 4 Metal Grey SILICONE €41.50
AiFlues

No 4 Metal Black EPDM

€27.00

No 4 Metal Black EPDM 76-152mm 250×250

APPLICATION
Suitable for profiled sheeting and flat panel surfaces and is temperature resistance -55°C to 135°C.

CONSTRUCTION
Made of EPDM, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light.
The one piece construction allows for quick and easy on-site installation – usually taking no longer than five minutes.
The base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.

INSTALLATION
1. Choose pipe opening and trim using a stanley knife or scissors.
2. Slide flashing over pipe (you may need to lubricate the flashing with some grease).
3. Form the flashing to the same profile as the roof.
4. Apply sealant (contained in the Fixing Kit).
5. Fasten using the screws and caps (supplied in the Fixing Kit).

ONE Standard Fixing Kit is required to install this flashing.

Add to wishlist
Category: Tags: ,
Description

APPLICATION
Suitable for profiled sheeting and flat panel surfaces and is temperature resistance -55°C to 135°C.

CONSTRUCTION
Made of EPDM, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light.
The one piece construction allows for quick and easy on-site installation – usually taking no longer than five minutes.
The base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.

INSTALLATION
1. Choose pipe opening and trim using a stanley knife or scissors.
2. Slide flashing over pipe (you may need to lubricate the flashing with some grease).
3. Form the flashing to the same profile as the roof.
4. Apply sealant (contained in the Fixing Kit).
5. Fasten using the screws and caps (supplied in the Fixing Kit).

ONE Standard Fixing Kit is required to install this flashing.

 

 

 

Additional information
Brand

Material

Black EPDM Rubber
CE Approved

Yes
Max Operating Temperature

100°C Continuous – 135° Intermittent
Roof Pitch

0-18°
Size

250mm x 250mm
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “No 4 Metal Black EPDM”

Your email address will not be published. Required fields are marked *

Shipping & Delivery
pellet-stoves 2

SHIPPING

  • Dispatch for delivery normally takes up to two weeks, depending on availability. It can take up to six weeks for special orders in some instances, if the lead time is longer than six weeks you will be informed by email of the estimated lead time for your goods.

DELIVERY

  • Your goods will be delivered by our Courier network or our In-House Delivery team.
  • Many Stoves are very heavy. There will be one driver who will help, but we suggest you have at least one other person with you to assist.
  • The driver will move the stove to the nearest wheel point, depending on access. The driver will be unable to move the goods across gravelled, or unfinished drives, through narrow openings, or up steps.
  • If you are unavailable when your palletized stove is delivered at your pre-booked time, then re-delivery charges may apply.

Please see our full Shipping & Delivery guide is our Terms & Conditions

User Manuals

Related products

pellet flue
Compare

Pipe with Door 250mm – Ø 80

€43.50
Rigid fixed 250mm pipe with built in access door to enable sweeping of the flue pipe. This is only suitable for N1 pressure situations. effective installed length of 210mm.
APPLICATION Suitable for gas, oil and solid fuel appliances with temperatures up to 600° C. AI-Pellet pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System. AI-Pellet pipe should NOT be used to pass through ceilings or combustible walls. CONSTRUCTION AI-Pellet is a single skin connecting flue system manufactured in zero carbon steel with vitreous enamel coating in a matt black finish. Suitable for gas, oil and solid fuel appliances with temperatures up to 600 degrees C, When fitted with a seal a P1 pressure rating can be achieved up to a working temperature of 200 degrees C T200.
Add to wishlist
Select options
Quick view
pellet flue
Compare

Tee Cap – Ø 80

€23.50
Tee cap is used to cap off the base of a tee. It comes complete with a joint clip and allows access for sweeping purposes. APPLICATION Suitable for gas, oil and solid fuel appliances with temperatures up to 600° C. AI-Pellet pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System. AI-Pellet pipe should NOT be used to pass through ceilings or combustible walls. CONSTRUCTION AI-Pellet is a single skin connecting flue system manufactured in zero carbon steel with vitreous enamel coating in a matt black finish. Suitable for gas, oil and solid fuel appliances with temperatures up to 600 degrees C, When fitted with a seal a P1 pressure rating can be achieved up to a working temperature of 200 degrees C T200.
Add to wishlist
Select options
Quick view
Compare

Size 1 High Temp Grey SILICONE Size 80-200mm

, ,
€80.00
Suitable for tiled or slate roofs with external pipe diameters of 80mm to 200mm The aluminium base size is 605mm x 505mm, suitable for high temperatures APPLICATION Suitable for tiled roofs and is temperature resistance -74°C to 260°C CONSTRUCTION Enviromentally safe lead free aluminium base. The SILICONE rubber upstand has a 20 year life. The built in 20° pitch allows adaptability to almost any roof pitch including 45°. The pull tab design and easy smooth tear grooving is intended to eliminate cutting by knife and allow for a circular hole. INSTALLATION 1. Pull tab design to correct size using pliers, alternatively cut using a stanley knife. 2. Apply silicone sealant to back of flashing. 3. Remove tiles around pipe and slide flashing over pipe. 4. Fasten Flashing to the roof. 5. Cut tile to fit to the top of the Flashing allowing the bottom of the flashing metal base to sit on top of the tiles.
Add to wishlist
Select options
Quick view
Pellet Flue
Compare

90° Tee with Female Connector – Ø 80

€44.50
The 90° Tee female connector is usually installed when you are connecting the flue to the rear outlet of an appliance, the branch of the tee has a female branch so it can fit over the out let spigot of the appliance. A tee cap is sold separately for the base of the tee to allow sweeping access. APPLICATION Suitable for gas, oil and solid fuel appliances with temperatures up to 600° C. AI-Pellet pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System. AI-Pellet pipe should NOT be used to pass through ceilings or combustible walls. CONSTRUCTION AI-Pellet is a single skin connecting flue system manufactured in zero carbon steel with vitreous enamel coating in a matt black finish. Suitable for gas, oil and solid fuel appliances with temperatures up to 600 degrees C, When fitted with a seal a P1 pressure rating can be achieved up to a working temperature of 200 degrees C T200.
Add to wishlist
Select options
Quick view
flue pipe
Compare

Connector Female – Female – Ø 80

€22.50
Connector Female/Female is double ended change over pipe. APPLICATION Suitable for gas, oil and solid fuel appliances with temperatures up to 600° C. AI-Pellet pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System. AI-Pellet pipe should NOT be used to pass through ceilings or combustible walls. CONSTRUCTION AI-Pellet is a single skin connecting flue system manufactured in zero carbon steel with vitreous enamel coating in a matt black finish. Suitable for gas, oil and solid fuel appliances with temperatures up to 600 degrees C, When fitted with a seal a P1 pressure rating can be achieved up to a working temperature of 200 degrees C T200.
Add to wishlist
Select options
Quick view
Compare

Storm Collar – Ø 80

€20.00
Used to ensure water tightness in the passage through the roof. It also protects the flashing from extreme weather conditions. Its should be installed about 25mm above the tallest part of the flashing ConvesaTWPro Fit System Super easy assembly, It takes one second and the one hand to put two parts together including attaching the locking band! The wall bands are embedded in to the pipe itself, so no protrusions between one section to the next. APPLICATION For use on solid fuel and gas/oil appliances. eg: Pellet Stoves, woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.
Add to wishlist
Select options
Quick view
pellet flue
Compare

Pipe 500mm – Ø 80

€23.50
Rigid fixed 500mm pipe effective installed length of 460mm. APPLICATION Suitable for gas, oil and solid fuel appliances with temperatures up to 600° C. AI-Pellet pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System. AI-Pellet pipe should NOT be used to pass through ceilings or combustible walls. CONSTRUCTION AI-Pellet is a single skin connecting flue system manufactured in zero carbon steel with vitreous enamel coating in a matt black finish. Suitable for gas, oil and solid fuel appliances with temperatures up to 600 degrees C, When fitted with a seal a P1 pressure rating can be achieved up to a working temperature of 200 degrees C T200.
Add to wishlist
Select options
Quick view
pellet flue
Compare

90° Tee – Ø 80

€40.00
The 90° Tee is usually installed when you are connecting the flue to the rear outlet of an appliance, a tee cap is sold separately for the base of the tee to allow sweeping access. APPLICATION Suitable for gas, oil and solid fuel appliances with temperatures up to 600° C. AI-Pellet pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System. AI-Pellet pipe should NOT be used to pass through ceilings or combustible walls. CONSTRUCTION AI-Pellet is a single skin connecting flue system manufactured in zero carbon steel with vitreous enamel coating in a matt black finish. Suitable for gas, oil and solid fuel appliances with temperatures up to 600 degrees C, When fitted with a seal a P1 pressure rating can be achieved up to a working temperature of 200 degrees C T200.
Add to wishlist
Select options
Quick view